Author: woodshoplifepodcast

Tool Purchase Regrets, Most Useful Tool, CAD Software

Brian’s Questions:

Hey guys,

First of all, thanks for the most helpful woodworking podcast around! My question(s) revolve around a home library project. I’m planning on bookcases on all four walls of a small room and wondering how you’d approach that, specifically:
(1) what would you do about the inside corners of the room where two sets of bookcases come together? Just blank them off? Something else?
(2) as far as the cases themselves, for cost reasons, I’m planning to do 3/4 plywood carcasses close to 8’ high with one fixed shelf in the middle (Domino construction) and shelf pins for the rest of the shelves. How wide can I reasonably go without sag in the shelves? Is one fixed shelf enough for stability or do I need two, say? Do I need a plywood back on each case?
Any other general tips on a library project or this type?
Thanks! Mat

What tools you guys do regret to buy?
Marcello

Alright fellas first question from me. I finally got a Makita track saw and went for the full 110″. I’m going to tear down my old 2×4 oversized work bench and start over with a nice miter saw / work area cabinet wall.
My plan is to go about 30″ deep to accommodate my DeWalt sliding dual bevel giant miter saw while also giving me ample assembly area. Maybe an mft style work area on one side, maybe t tracks here and there.
I’m going to leave it a little open ended for you guys to play around with the idea. What would your dream work area like this include? No limits, all the bells and whistles. No one to tell you no.
Thanks for taking my question. Jim G.

Huy’s Questions:

Hi Guys,
Really enjoy the podcast and all the useful information. I wrote before about a walnut table I am making. I have a couple of questions. I looked at the walnut at the local lumber yard. Great selection but lumber is pretty expensive. Question 1: The lumber distributor has a great selection. For the table top should I spring for quarter sawn at roughly 1/3 more per board foot? Question 2: I am trying to bring some order to chaos in my shop and am considering some shop cabinets. a) should I consider casters? b) should I spend the extra to install side mount drawer slides or will homemade runners be good enough?
Thanks for your help and the great podcast.
-Scott

Good day guys..My question is probably primarily for Huy.
I am getting back into woodworking after a lengthy hiatus to a career that did not allow me the time. Now that I do have the time, I am diving right back in. I am a lifelong contract mechanical designer, and have been a SolidWorks user/license holder since 1999, dont do the math on how much that has depleted my bank account in the past 24 years, and I am no rocket scientist like Huy, I have only done work on 70 ton vehicles designed outside detroit.
SolidWorks is amazing, and I have designed many projects for my woodworking with it. However I feel it is a bit heavyweight on the design side for the projects I want to do. I want to be working in my shop, and not spending hours designing parts, making assemblies etc. Dont get me wrong, the end results are incredible on the design side, but design for my woodworking shoudlnt be 60% on SolidWorks and 40% on tools. Any suggestions for the best solution for this? I have not spent alot of time researching, but have looked into Fusion360 and other solutions but not greatly as I know there will a thought process change required.
I am just looking for something simple, quick and of course accurate. We live in a 3d world, and that is an important aspect for me.Thank you so much.
Kurtis, DutchMillWorks

Hey guys, Josh here, hope this is the right way to contact you all. My question is, what machine do you think you can get away with in order to produce the most projects? I was thinking a lathe for drinkware, baseball bats and so on depending on a mini, midi or full size lathe. But I’m no expert by any means, I only had a couple years of shop experience in school and most of the terminology has escaped me since, but all the hands on experience is still fresh in my mind and I’m hoping to get this hobby started up again. Thank you. Joshua

Sapwood is Evil, Dream Client, How Thick Should It be? and MORE!

Brians Questions:

Hi guys, thanks for such a great podcast. You recently got me through the journey back from a road trip to Montreal, although when my wife heard you guys, she was like, “What the -hell-are you listening to?!” But then she fell asleep so we had no problem (don’t worry, she wasn’t driving at the time).

My question is about evening out the sapwood and heartwood colour in walnut, so you can maximise the yield from boards and slabs. Do you have a particular process and/or product you’d recommend here? If your solution is to simply cut it off, it seems a shame to waste all that wood… have you found any good uses for it? Phil Evans

Hi – I am building a seating bench out of figured ash. I’d like to give it a gentle brown color and really accentuate the curly figure in the wood. I’m worried that stain won’t do much to bring out the beauty in it; should i use dye instead? What steps should I go through to highlight the figure? I don’t have a spray solution, so whatever finish will need to be wipe on or brush on. I prefer to avoid rattle cans of finish too, for what that’s worth. Mark

Guys Questions:

I recently had the client that all woodworkers dream of. Came to me literally saying money didnt matter and they wanted a high quality coffee table. I loaded it with design features and in the end it became my highest priced commission to date at over $12k for this 42″ square coffee table. I say that mainly to encourage others that there’s still people who will pay for quality. Anyway my question is that one of the design ideas i pitched this customer was to do a herringbone pattern on the sides of the table using shop sawn veneer. This will be my first time ever making veneer and doing anything with it. What tips can you give me? I have a VERY high quality bandsaw, the Laguna LT18 equipped with a Resawking blade. I do not have a drum sander. I plan to now get a Vacupress 300 for the task. What else should I know about veneering a herringbone pattern? AZ Custom Furniture Bilder

Hi Guys, thanks for the helpful podcast. I’ve been building furniture for a few years now and as a newish woodworker I have tried many different finishes in the pursuit of finding the one and only one. My question is, do you keep a log of which pieces of furniture have which finish so that you can see how they age and for when/if repairs or refinishes are needed? Thanks, Patty

Huy’s Questions:

Thanks for the podcast, guys!

My question: I’m building a sideboard for utilitarian storage when entering from the garage.
It is mostly cherry, will have a cherry top and is about 22″ deep by 60″ wide and 30″ tall.

I’m planning to use 8/4 cherry for the top, with a resulting thickness of whatever results from jointing and planing the boards to be edge glued for the top. Would there be any advantage in building the top from 4/4 boards face glued to make up the 8/4 thickness? I will be chamfering the bottom of the top so that any glue line would not be visible.

Thanks so much,
Bob Clark

Hi fellas,
I first want to say thank you for developing and producing this podcast and sharing your experience with the rest of mere mortals of woodworking. I am a nights and weekend hobbyist woodworker, making small projects for friends and family or DIY projects around the house. I am fortunate to have a modest collection of tools and enjoy trying new things and learning how to up my game. My question is really more about the process of using steel wool and vinegar to ebonize some red oak I’m making into a small case with a couple of drawers. The way I understand the process is that the combination of the steel wool and vinegar ultimately reacts with the tannins in the red oak, turning it darker (I’m hoping black). I’ve also recently discovered Original Tried and True finish (polymerized linseed oil and beeswax) and really like the results I’ve got on a few projects I’ve used it on. Would ebonizing the red oak change how a finish like Tried and True works? Is there a better finish in your opinion? How would each of you finish this if black was the end result, and FYI I don’t have spraying equipment. Thanks again for all you do for the woodworking community!
-Trevor

Bandsaw Blades, Pricing Work, Making Drawers, And More!!

Brians Questions:

Gentlemen,
Thank you so much for this podcast. I very much look forward to each episode. I primarily work with hand tools making traditional furniture. One of the few machines I own is a PowerMatic 15” bandsaw. Guy’s positive review of it sealed my decision and I’m very happy with it. Fantastic bandsaw. I mostly use it for long straight cuts and keep the Laguna 3/4” carbide tipped blade in it. On the occasions I need to make curve cuts I hate to change out blades. Call me lazy. I’d like to get another tool for this other than doing it by hand. It could be a smaller band saw with a thin blade, the DeWalt DW788 scroll saw, or something else. Mostly cuttin 4 quarter stock but on occasion eight quarter stock. What would you get and why? I also own a Makita corded jigsaw. Many thanks and keep up the great work.
Sincerely
Joe Leonetti.

Having two friends recently experience serious injuries while using their table saw, I am continuing to do more ripping using my bandsaw for safety sake. (I, like my two injured friends are in our 70’s- not as quick in our reactions, as good in our judgements or dexterous as when younger.) I’m fortunate to have two bandsaws, one of which I keep a 1/2” blade on for the purpose of resawing and ripping, so it works out quite well. The issue is the rough edge left by the bandsaw vs the smooth “gluable” edge that the table saw produces. What’s the best way to address this? I’ve heard mention of using a jointer after ripping – does this not introduce uncertainty as to the final width of the piece just ripped? For example, if I wanted a piece 10” wide and ripped it to 10 1/16”, I’d have to have my jointer set to remove exactly 1/16 which even if I accomplish that setting, may be hard to achieve and also get a perfect 90 degree edge. As an aside- I’m still considering selling my Powermatic and getting a Sawstop in the interest of increased safety. While some people might scoff at that idea, I don’t care-to each his own. Both of my two friends injuries were ugly, debilitating and expensive. Thanks for the best and most informative woodworking podcast! Tim Deal

Guys Questions:

Hello Huy and Guy, and welcome to the show Brian. My question today is about quoting pricing for inconvenience. What I mean by that is this: if a client comes to you with a request that you aren’t really excited about does that affect how much you quote? Do you ever give them a high quote in the holes that they say no, but high enough that if they still say yes, it offsets any frustration you expect to have while building?
Thanks, and I’m still waiting for Brian’s social media… and for Guy to say specificity again.
Joshua.

Huy’s Questions:

Great podcast guys. I Really appreciate how you guys answer questions based on your individual experiences. I like hearing 3 or 4 different ways to perform a task using a variety of tools. My question: my current home has 1/2” particle drawer boxes and I’m replacing them. What would you recommend for drawer box construction concerning material, thickness, drawer bottom thickness, and finish. Thanks.
-Eric Brown

Greetings Gentlemen,
Thank you for continuing your podcast into 2023. It’s very informative, but in a relaxed and casual format. Also; a welcome to Brian. Sean was a long time co-host and will be missed but Brian has slipped into his slot with ease and is doing great.

My question today is about planing. I’m making a 4×6 ft table top out of true 1-1/8 inch thick x 6 inch wide, rough cut white oak. When dressing down the wood, I plan on jointing one surface then planing the other surface parallel. Finished thickness I think will be between ¾ and 7/8. Here is the question. How important is it to take equal amounts off of each side? Can I just joint one surface and plane the opposite down to my finished thickness or do I have to try to take an equal amount off of both sides. If it matters, the lumber is kiln dried down to 7%.

Terry W.

Small Shop Layout, Woodworking Software, Tool Storage and MORE!

Brian’s Questions:

I’ve recently walled off the third bay of my three car garage to give me a smaller space to heat and a wall to work with. I have started thinking about my ~270 sqft shop in three dimensions trimming all the fat and maximizing my functionality.What would you guys do with a nice healthy 11ft ceiling height considering I want pretty much my entire shop to exist is this space. What type of ideas would you have for multi functioning furniture? What would you put on the walls? Everything that can be is already on wheels. I’ve got most every major tool you guys do. Just curious on your take. How would you cram yourselves into this little space or do you already?
Thanks for continuing the podcast. -Jim G.

I am building an outdoor bench using steel legs and a currently rough cedar top. I plan on sanding the cedar smooth and finishing it. What would be the best grit to sand to, and what finish should I apply? It will get all-day full sunlight.
Jason H.

Guy’s Questions:

Hi: As I have said before, this is the best woodworker podcast on the planet! I enjoy so much the focus on woodworkers questions. Your personalities shines through as well as your intellect and your skills as a woodworker. Thanks so much.
My question stems from a recent project I started. I tried to be more exacting. I designed the project on gridded paper, figured out each exact dimension and then started to calculate the wood requirements. I figured out the sheet goods by figuring out the rough layout of the parts on a scale grid diagram. Then I calculated the board feet of each of the solid wood parts using a board feet calculator app a selecting 10% for waste option. I then added them up and got ready to buy the necessary wood.
In the past I just winged it. I’d have a rough drawing on scrap paper and a guess at the wood requirements which often meant follow-up trips to the store. Projects often had a few rework, redesign elements on the fly and some issues that hopefully I could only see, hence the change to more exacting.
I have a few questions. How exact are you with your designs? Is this the process you go through before purchasing wood? Is there another way? Do you use any apps like:”BoardFeetEasy” or “SmartCut”? Do you use any other woodworking apps? If so which ones? Is 10% a good waste figure? Do you adjust the waste figure based on any criteria? What are the criteria?
Thanks again for you’re time, focus and insite into the craft of woodworking.
Regards,Joe James

Hi, thanks for all the great work on this podcast. Yours is the only one that actually I even have a dedicated podcast app set up for, so that you guys are only a couple taps away for my sausage fingers whenever I have a free moment and want to learn something. Anyway, my question is about using a dryer plug for 220V machines. I’m planning a couple new tools for my basement shop, and whilst my first choice is to add a dedicated 220 line, I’d rather space things out financially if I can. One option seems potentially to use the dryer electrical socket until I have the cash flow to run dedicated electrics. I’m seeing mixed things in my research and wondering if you have any real world experience on using dryer plugs for tools with an adapter/extension, specifically if it’s a hazard and the pros/cons? In my case the tools would be a Hammer A326 and Sawstop PCS 3HP. Thanks for any advice you can offer and keep up the great work. Phil Evans

Huy’s Questions:

Hi guys, love the podcast! Thanks for all you do! I’m designing my first piece of larger furniture, an entry way table. I am planning 3 drawers across the top, and below that a cabinet in the center and open shelves to either side. I’m wondering how you guys decide on proportions for a build like this. Supposedly the 1.618 is some kind of magic formula that makes everything perfect, but how do you use it, or do you even bother? What if the piece has to fit a certain space, do you take that into account? Help me woodshop life, you’re my only hope! Matt

Hello all, how about another shop storage question? I’ve been primarily a power tool user for many years, but have started building a hand tool collection over the last 2 or 3 years. Im finding the “hybrid” approach more to my liking and feel it’s certainly improved the quality of my projects with the ability to fine tune fit and finish. Now being the proud owner of quality chisels, a few hand planes, scrapers and so on, most of the tools are in a tool box drawer.
I want to get these commonly used items out of the drawer and in reach, but I find myself starting to plan and build tool holders or storage solutions only to scrap it and move onto something else because I get lost in how simple or complex to make it.
I need to just shut up and do it, I know this. In your opinions, when you need a storage solution, do you just make whats basic and functional and after some use fine tune or remake it when needed? Or, do you spend time laying everything out and aiming for a one and done build?
-Mike

Making Your Own Dominos, Painting Your Projects, Plywood or MDF? and MORE!

Brian’s Questions:

Hey Fellas,
I’m in the market for a new table saw. I am coming from a 2hp Grizzly hybrid saw with a broken part I cannot find a replacement for. I’m debating between a 3hp Powermatic or Sawstop. Either of these will be a major upgrade from what I have but do you have opinions either way? The Sawstop technology is great and I understand accidents can happen but I tend to think if your hands are that close to the blade you’ve got bigger problems. That said, the Sawstop is up to $1,000 cheaper than the powermatic depending which add-ons you choose. Do you have any thoughts or are there other brands I’m missing and should look into?
Chris
Instagram: @custom_by_chris

Hi guys! I am a hobbyist/turning professional woodworker based in Portland, Oregon. I have really enjoyed listening to your podcast and thought I would quickly ask your opinion on rectangular dominos.
I have been creating shop-made dominos to save money. Creating them is a pain in the butt! Trying to nail metric round-overs with imperial bits at that level of precision is pretty involved. It usually takes a bit of time and wasted material to set the router table up correctly in order to batch a bunch out. Then running a glue groove on everything is another step that takes time. A thought came to me about creating square edged, rectangular tenons that aren’t hitting the radii of the domino mortise. My thought is that the few millimeters of void wouldn’t really affect the strength of the joint and the voids themselves would act as a hydrolock prevention by nature. Assuming these aren’t used for through style tenons, do you see any issues using rectangular stock? Thanks for doing the podcast and I look forward to future episodes!
Sal Al-Sudairy
sfapdx@gmail.com
@oregon_woodworks Instagram

Guy’s Questions:

Hey Guy’s

I know finishing gets hit often but this is perhaps a different spin. My basement garage is my workshop so odor and chemical safety is a concern.
I’m mostly done with my plywood/poplar painted dresser (thanks for the tips by the way, screwing and glueing without fancy jointery made assembly a breeze Guy).
That being said what is a good low odor option for finishing a paint grade project that’s being painted white? Yellowing and tannin bleed are therefore both concerns.
I’ve heard Ya’ll talk about conversion varnishes but also heard complaints about odor. Would BIN water based primer under enamel paint be best? Should I go the oil based primer/paint route for durability?
I have recently gotten a paint sprayer but am open to rolling if that’s preferable. I’ll attach my budget sprayer below for context.
Thanks so much, this is by far the best woodworking podcast.
-Dave

Hello Huy, Guy, and Brian! You gentlemen, as well as Sean, have been a huge help and inspiration to my woodworking journey. Keep the great content coming!
I recently picked up an older Bosch 1615 evs plunge router mounted to an old tabletop with an Incra Intelli fence. While I can find manuals online for both of these discontinued items, I’d like to get your input on how to best set up an older router with this fence. Since this particular router is in its own molded housing, I don’t think a router lift is an option. What do you all recommend for setting this router up in a new table? I intend to likely build a stand-alone router table with a top made with melamine left over from a recent project, but I’m open to suggestions. Thanks, -Kurt

Huy’s Questions:

Hi everyone,
Thank you for a great show. I’ve listened through the entire catalog twice, learning a lot.
In Episode #115 (and other episodes) you mention UV light turning walnut orange. I recently built a large dining room table out of walnut. I did not dye the table, even though I knew color change was possible. I have never used dye and the walnut was so stunning, I was afraid I would mess it up.
If my table turns orange, can it be sanded off? How deep does the UV “damage” go into the wood?
If I was to dye the walnut, could you please remind us what color dye you have used that works on walnut? How you have applied it to walnut, and when in the finishing process?
hanks again for a great show and a great woodworking education.
Kevin

Hello Gentleman,
Love the podcast. Thanks for all your hard work.
I am considering tackling a Entertainment unit for my bonus room; however I am struggling with material choice. The cabinet finish will be painted, do you suggest plywood or MDF? I plan on building some drawers with plywood boxes and MDF faces but I am concerned about the durability of the MDF when installing hinges if I use it for the carcass construction.
The overall length of this build is 16″ long by 8′ tall with drawers along the bottom open shelving on either side of that with the TV in the middle. Normally I am not so indecisive ; however this is such a large project and with the high cost of materials I want to start off on the right foot. Any guidance would be appreciated.

  • Mike