This Episode’s Quesions:
Brians Questions:
I plan to build a handtool workbench in the future, maybe in a year or so, but as of right now, I do not have any workholding devices. I have a large assembly table that does have an overhang and the top is 1.25″ thick. I have been using clamps to the top as a stop for planing and it does not work very well. I also need a way to hold the wood for using chisels, and I haven’t bought any dovetailing tools yet because of the lack of workholding devices. Are there any good vises that don’t require cutting a hole in my assembly table or makeshift ways to hold the wood until I can build a proper bench? Thanks Jeff
When sanding end grain, say when you’ve got a panel where you’ve chamfered or rounded over the edge, which direction should you sand? I’d imagine you continue to follow the grain direction from the adjacent face grain but I’m not sure. Can you sand across the grain? Thanks for the great podcast, you guys really do have the best wood working show out there! Eric
Guys Quesions:
Hey Guys
I am looking to set up a shop in my unheated garage. I live in Canada so the weather is inconsistent. Very cold in the winter and very hot and humid in the summer. I am thinking of setting up a small workbench in my basement to cut joinery and do glue ups/assembly. I would keep all of my big power tools( table saw, planer etc.) in the garage. This setup would allow me to work comfortably through the year. My question is with wood movement.
If I stored wood in my air conditioned basement and just took it out to the garage for a few hours at a time to plane and cut to size and then brought it back inside to cut joinery with hand tools, would the few hours spent in the humid or cold garage be enough time to warp the boards after I brought them back in?
Heating the garage isn’t a realistic option right now as I have two young children and would probably only be able to get a few hours in the shop a week. (Not worth the cost)
Thanks for all of the help. This podcast has been a huge influence in helping me to get started with woodworking. Derek
I have a small benchtop jointer that a friend gave me for free and a Dewalt 735 planer. For anything but pretty small parts, I use a sled to joint lumber in my planer. I’d like to upgrade both of these eventually. I have a big shop with plenty of power, so neither of those are an issue. My budget is generally the limiting factor. I do plan to keep using standalone machines for the convenience of maintaining settings and flexibility of workflow. I’d like to get a big jointer first and keep using the 735 while I save up for a big, heavy 220v planer. My question is about 12 inch combo machines. I keep seeing decent 12″ combo machines come up used for way less than I can find a standalone 12″ jointer. I’ve seen a few of the Jet machines for $2k-$2500 and a friend recently got a Hammer A3 31 for $3500. Even new, combo machines seem to run way cheaper than a 12″ jointer. Why? I understand the beds are shorter, but other than that, what is the disadvantage. Is it ridiculous to buy one if I have no long term need of the planer function and don’t plan to use it? Parker
Huys Quesions:
Hey guys,
Thank you for your many thoughtful responses to the questions you receive from your listeners.
I tend to get bored after I’ve made the same type of project several times (ie pencil boxes, pens, etc..).
If I am not in a time crunch, I like figuring out how to do something to make a project a little more challenging and interesting.
I like looking at projects to give me some inspiration on how I might make a new project. Early on in my woodworking journey I gained a lot of positive inspiration from watchin ‘New Yankee Workshop’.
The way Norm broke down processes in his projects was very helpful to me.
However, there are some projects I’ve seen which are incredibly intimidating.(ie highboys, Maloof rockers, etc…). While I admire these types of projects, I don’t think I would tackle them without taking a specific class.
Where do you guys find inspiration for you projects?
Are there any type of projects that intimidate you?
Thank you for your responses.
Have a great day.
Chuck
I am designing a dresser which will be 48” high and 72” wide and a chest of drawers which will be 60” high and 40” wide. I would like to join the carcass sides and top with dovetails. With the sides being 48” and 60” and the width being 72” and 60”, how should I clamp the sides and top/bottom to my bench and stand in order to cut the dovetails by hand? I’m only 5’8” and have never cut dovetails up by my head. With a dresser and chest of drawers being the above sizes, would you recommend another method for my joinery?
Love the podcast, keep up the great work!!
Mike
